[ Pobierz całość w formacie PDF ]
INSTALLATION.)
3. Remove the driver-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
4. Disconnect the connection between the pillar antenna and the front antenna feeder.
5. Remove in the order indicated in the table.
1 Clip
2 Front antenna feeder
6. Install in the reverse order of removal.
End Of Sie
X3U920WAD
FRONT ANTENNA FEEDER INSPECTION
A3U092066941W02
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.) (See 09 20 6 AUDIO UNIT
INSTALLATION.)
3. Remove the driver-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
4. Disconnect the connection between the pillar antenna and the front antenna feeder.
5. Verify that there is no continuity between the front antenna feeder terminals A and B using an ohmmeter.
" If not as specified, replace the front antenna feeder.
6. Inspect for continuity between the front antenna
09 20
feeder terminals using an ohmmeter.
" If not as specified, replace the front antenna
feeder.
X3U920WAE
X3U920WAF
End Of Sie
REAR ANTENNA FEEDER REMOVAL/INSTALLATION
A3U092066942W01
1. Disconnect the negative battery cable.
2. Remove the right-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
3. Remove the right-side A-pillar trim. (See 09 17 10 A-PILLAR TRIM REMOVAL/INSTALLATION.)
4. Remove the headliner. (See 09 17 16 HEADLINER REMOVAL/INSTALLATION.)
5. Disconnect the connector between the rear center roof antenna and rear antenna feeder.
6. Disconnect the connector between the front antenna feeder and rear antenna feeder.
7. Remove in the order indicated in the table.
1 Clip
2 Rear antenna feeder
8. Install in the reverse order of removal.
End Of Sie
Y3A8124W004
09 20 5
1712-1U-01G(09-20).fm 6 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
REAR ANTENNA FEEDER INSPECTION
A3U092066942W02
1. Remove the rear antenna feeder.
2. Verify that there is no continuity between rear antenna feeder terminals A and B using an ohmmeter.
3. Inspect for continuity between the rear antenna
feeder terminals using an ohmmeter.
" If not as specified, replace the rear antenna
feeder.
A3U0920W101
Y3A8124W002
End Of Sie
AUDIO UNIT REMOVAL
A3U092066900W01
1. Disconnect the negative battery cable.
2. Remove the hole covers by inserting a small
tape-wrapped screwdriver into the slot and
carefully pry them off without scratching the
center panel. Pry up and pull off the hole covers
carefully to prevent the posts from breaking off.
3. With the beveled parts of the SST facing inward,
insert them into the unit.
Note
" Two sets of the SSTs are necessary to
remove the audio unit.
YDE81241201
4. Pull the SST outward and forward to slide out the
unit.
5. Disconnect the connectors and antenna jack.
End Of Sie
YDJ8124W107
AUDIO UNIT INSTALLATION
A3U092066900W02
Caution
" Make certain that the wiring harness and antenna feeder are not caught between the unit and
"
"
"
dashboard. If the harness or the antenna feeder is caught between the unit and dashboard, it may
become the cause of trouble or malfunctions.
1. Connect the connectors and antenna jack.
2. Insert the unit until each clip clicks into place.
Caution
" To install audio unit, be sure to push
"
"
"
service hole cover areas on both sides of
the audio unit. If switches are pressed
instead, it may become the cause of
trouble or malfunctions.
3. Install the service hole covers.
4. Connect the negative battery cable.
YDJ8124W108
End Of Sie
09 20 6
1712-1U-01G(09-20).fm 7 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
UPPER MODULE REMOVAL/INSTALLATION
A3U092066900W03
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
1 Screw
(See 09 20 7 Screw Installation Note)
2 Upper module
(See 09 20 7 Upper Module Removal Note)
3 Cover
(See 09 20 7 Cover Removal Note)
4. Install in the reverse order of removal.
Y5J8124W004
09 20
Upper Module Removal Note
1. Insert a screwdriver into the hole stamped mark.
2. To remove upper module, lift it by pushing down
the screwdriver s handle.
YLE8124W005
Cover Removal Note
1. Insert a tape-wrapped screwdriver between the
cover and the base unit, then unlatch hook A.
2. To unlatch hook B, pull the cover upward.
YLE8124W006
Screw Installation Note
Caution
" If an undesignated screw is used, the inside of the upper module could be damaged. When
"
"
"
installing the module, be sure to use a designated screw (red).
09 20 7
1712-1U-01G(09-20).fm 8 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
End Of Sie
LOWER MODULE REMOVAL/INSTALLATION
A3U092066900W04
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
1 Cover
(See 09 20 8 Cover Removal Note)
2 Screw
(See 09 20 8 Screw Installation Note)
3 Lower module
4. Install in the reverse order of removal.
YLE8124W007
Cover Removal Note
1. Insert the SST into the service holes on the bottom surface of the lower module.
2. To remove the cover, push the SST in the
direction shown by the arrow.
ZLU0920W003
Screw Installation Note
Caution
" If an undesignated screw is used, the inside of the upper module could be damaged. When
"
"
"
installing the module, be sure to use a designated screw (red).
End Of Sie
CIGARETTE LIGHTER REMOVAL/INSTALLATION
A3U092067000W01
1. Disconnect the negative battery cable.
2. Remove the console. (See 09 17 5 CONSOLE
REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Cigarette lighter plug
2 Connector
3 Socket
(See 09 20 9 Socket Removal Note)
4 Ring
(See 09 20 9 Ring Removal Note)
X3U920WAG
4. Install in the reverse order of removal.
09 20 8
1712-1U-01G(09-20).fm 9 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
Socket Removal Note
1. Turn the socket while pushing the protrusion of
the ring through the hole of the socket with a
tape-wrapped screwdriver.
2. Push the socket forward.
X3U920WAH
3. Return the socket clockwise to original angle
position as shown to pull it out forward.
09 20
X3U920WAJ
Ring Removal Note
1. Pull the ring forward while pushing the tabs.
End Of Sie
Y3U920WA3
CIGARETTE LIGHTER INSPECTION
A3U092067000W02
1. Turn the ignition switch to ACC position.
2. Verify that the cigarette lighter plug will move normally within 10 20 seconds, after pressing the plug into the
socket.
" If the cigarette lighter does not operate normally, replace the cigarette lighter and socket. (See 09 20 8
CIGARETTE LIGHTER REMOVAL/INSTALLATION.)
End Of Sie
09 20 9 [ Pobierz całość w formacie PDF ]
zanotowane.pl doc.pisz.pl pdf.pisz.pl chiara76.opx.pl
INSTALLATION.)
3. Remove the driver-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
4. Disconnect the connection between the pillar antenna and the front antenna feeder.
5. Remove in the order indicated in the table.
1 Clip
2 Front antenna feeder
6. Install in the reverse order of removal.
End Of Sie
X3U920WAD
FRONT ANTENNA FEEDER INSPECTION
A3U092066941W02
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.) (See 09 20 6 AUDIO UNIT
INSTALLATION.)
3. Remove the driver-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
4. Disconnect the connection between the pillar antenna and the front antenna feeder.
5. Verify that there is no continuity between the front antenna feeder terminals A and B using an ohmmeter.
" If not as specified, replace the front antenna feeder.
6. Inspect for continuity between the front antenna
09 20
feeder terminals using an ohmmeter.
" If not as specified, replace the front antenna
feeder.
X3U920WAE
X3U920WAF
End Of Sie
REAR ANTENNA FEEDER REMOVAL/INSTALLATION
A3U092066942W01
1. Disconnect the negative battery cable.
2. Remove the right-side front side trim. (See 09 17 13 FRONT SIDE TRIM REMOVAL/INSTALLATION.)
3. Remove the right-side A-pillar trim. (See 09 17 10 A-PILLAR TRIM REMOVAL/INSTALLATION.)
4. Remove the headliner. (See 09 17 16 HEADLINER REMOVAL/INSTALLATION.)
5. Disconnect the connector between the rear center roof antenna and rear antenna feeder.
6. Disconnect the connector between the front antenna feeder and rear antenna feeder.
7. Remove in the order indicated in the table.
1 Clip
2 Rear antenna feeder
8. Install in the reverse order of removal.
End Of Sie
Y3A8124W004
09 20 5
1712-1U-01G(09-20).fm 6 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
REAR ANTENNA FEEDER INSPECTION
A3U092066942W02
1. Remove the rear antenna feeder.
2. Verify that there is no continuity between rear antenna feeder terminals A and B using an ohmmeter.
3. Inspect for continuity between the rear antenna
feeder terminals using an ohmmeter.
" If not as specified, replace the rear antenna
feeder.
A3U0920W101
Y3A8124W002
End Of Sie
AUDIO UNIT REMOVAL
A3U092066900W01
1. Disconnect the negative battery cable.
2. Remove the hole covers by inserting a small
tape-wrapped screwdriver into the slot and
carefully pry them off without scratching the
center panel. Pry up and pull off the hole covers
carefully to prevent the posts from breaking off.
3. With the beveled parts of the SST facing inward,
insert them into the unit.
Note
" Two sets of the SSTs are necessary to
remove the audio unit.
YDE81241201
4. Pull the SST outward and forward to slide out the
unit.
5. Disconnect the connectors and antenna jack.
End Of Sie
YDJ8124W107
AUDIO UNIT INSTALLATION
A3U092066900W02
Caution
" Make certain that the wiring harness and antenna feeder are not caught between the unit and
"
"
"
dashboard. If the harness or the antenna feeder is caught between the unit and dashboard, it may
become the cause of trouble or malfunctions.
1. Connect the connectors and antenna jack.
2. Insert the unit until each clip clicks into place.
Caution
" To install audio unit, be sure to push
"
"
"
service hole cover areas on both sides of
the audio unit. If switches are pressed
instead, it may become the cause of
trouble or malfunctions.
3. Install the service hole covers.
4. Connect the negative battery cable.
YDJ8124W108
End Of Sie
09 20 6
1712-1U-01G(09-20).fm 7 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
UPPER MODULE REMOVAL/INSTALLATION
A3U092066900W03
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
1 Screw
(See 09 20 7 Screw Installation Note)
2 Upper module
(See 09 20 7 Upper Module Removal Note)
3 Cover
(See 09 20 7 Cover Removal Note)
4. Install in the reverse order of removal.
Y5J8124W004
09 20
Upper Module Removal Note
1. Insert a screwdriver into the hole stamped mark.
2. To remove upper module, lift it by pushing down
the screwdriver s handle.
YLE8124W005
Cover Removal Note
1. Insert a tape-wrapped screwdriver between the
cover and the base unit, then unlatch hook A.
2. To unlatch hook B, pull the cover upward.
YLE8124W006
Screw Installation Note
Caution
" If an undesignated screw is used, the inside of the upper module could be damaged. When
"
"
"
installing the module, be sure to use a designated screw (red).
09 20 7
1712-1U-01G(09-20).fm 8 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
End Of Sie
LOWER MODULE REMOVAL/INSTALLATION
A3U092066900W04
1. Disconnect the negative battery cable.
2. Remove the audio unit. (See 09 20 6 AUDIO UNIT REMOVAL.)
3. Remove in the order indicated in the table.
1 Cover
(See 09 20 8 Cover Removal Note)
2 Screw
(See 09 20 8 Screw Installation Note)
3 Lower module
4. Install in the reverse order of removal.
YLE8124W007
Cover Removal Note
1. Insert the SST into the service holes on the bottom surface of the lower module.
2. To remove the cover, push the SST in the
direction shown by the arrow.
ZLU0920W003
Screw Installation Note
Caution
" If an undesignated screw is used, the inside of the upper module could be damaged. When
"
"
"
installing the module, be sure to use a designated screw (red).
End Of Sie
CIGARETTE LIGHTER REMOVAL/INSTALLATION
A3U092067000W01
1. Disconnect the negative battery cable.
2. Remove the console. (See 09 17 5 CONSOLE
REMOVAL/INSTALLATION.)
3. Remove in the order indicated in the table.
1 Cigarette lighter plug
2 Connector
3 Socket
(See 09 20 9 Socket Removal Note)
4 Ring
(See 09 20 9 Ring Removal Note)
X3U920WAG
4. Install in the reverse order of removal.
09 20 8
1712-1U-01G(09-20).fm 9 Ú0ü0¸0 ÿÿÿÿt^ÿgÿÿåe0Ñ‘Üfåe0HSMRÿÿBfÿÿR
ENTERTAINMENT
Socket Removal Note
1. Turn the socket while pushing the protrusion of
the ring through the hole of the socket with a
tape-wrapped screwdriver.
2. Push the socket forward.
X3U920WAH
3. Return the socket clockwise to original angle
position as shown to pull it out forward.
09 20
X3U920WAJ
Ring Removal Note
1. Pull the ring forward while pushing the tabs.
End Of Sie
Y3U920WA3
CIGARETTE LIGHTER INSPECTION
A3U092067000W02
1. Turn the ignition switch to ACC position.
2. Verify that the cigarette lighter plug will move normally within 10 20 seconds, after pressing the plug into the
socket.
" If the cigarette lighter does not operate normally, replace the cigarette lighter and socket. (See 09 20 8
CIGARETTE LIGHTER REMOVAL/INSTALLATION.)
End Of Sie
09 20 9 [ Pobierz całość w formacie PDF ]